part-list.md

Part List

This document contains the full list of all parts to build TesLight. The list has been split into required and optional parts. Since TesLight can be modified in a lot of ways, the actual part list depends a little on your individual plans. Make sure to read the planning document first. Also, this list assumes that you have all necessary tools and materials for building electronics projects, like a soldering iron.

Assembled PCB by JLCPCB

Most parts will come fully assembled with the board. The parts are already contained in the fiels for the board. You only have to insert the ESP32 board and the MPU6050 manually.

Part	Count	Source	Comment
TesLight PCB (SMT Service)	1	JLCPCB	Can be ordered from JLCPCB using board files from the project
TesLight Case	1	JLCPCB	Can be ordered from JLCPCB using 3D models from the project
AzDelivery ESP32 Dev Board	1	Amazon	Or compatible with same size and layout
MPU6050 Motion Sensor	1	Reichelt	Works without but is highly recommended
JST-XH 2 Pin Male	2	Reichelt
JST-XH 3 Pin Male	8	Reichelt
JST-XH 4 Pin Male	2	Reichelt
JST-XH Connectors	36	Reichelt	Maybe get a few more to be on the safe side

Self Assembly

Part	Count	Source	Comment
TesLight PCB	1	JLCPCB	Can be ordered from JLCPCB using board files from the project
TesLight Case	1	JLCPCB	Can be ordered from JLCPCB using 3D models from the project
AzDelivery ESP32 Dev Board	1	Amazon	Or compatible with same size and layout
MPU6050 Motion Sensor	1	Reichelt	Works without but is highly recommended
Micro SD Socket	1	Amazon
74HCT541D	1	Reichelt
LM2596T-5.0 Regulator.	1/2	Reichelt	Make sure to get the fixed 5V version
Inductor min. 33µH	1/2	Reichelt
IN5824 Schottky Diode	1/2	Reichelt
Capacitor 680µf	1/2	Reichelt
SMD Capacitor 10µf 10V	1	Reichelt
SMD Capacitor 100µf 10V	3	Reichelt
SMD Capacitor 220µf 10V	2	Reichelt
SMD Resistor 220Ω 125mW	9	Reichelt
SMD Resistor 1kΩ 125mW	1	???
SMD Resistor 4.7kΩ 125mW	1	Reichelt
SMD Resistor 2.2kΩ 125mW	2	Reichelt
SMD Resistor 6.65Ω 500mW	1	JCSC
Zener Diode 3.0V	1	Reichelt
Fuse and Holder 5A	2	Reichelt
Poly Fuse 3A	1	Reichelt
JST-XH 2 Pin Male	2	Reichelt
JST-XH 2 Pin Female	2	Reichelt
JST-XH 3 Pin Male	8	Reichelt
JST-XH 3 Pin Female	8	Reichelt
JST-XH 4 Pin Male	2	Reichelt
JST-XH 4 Pin Female	2	Reichelt
JST-XH Connectors	36	Reichelt	Maybe get a few more to be on the safe side

Possible LEDs

Part	Source	Comment
WS2812 LED Strip	Amazon
Fiber Tube	Amazon
LED Injector Case	JLCPCB	Can be ordered here using 3D models from the project
LED Light Bars	IYC	30 cm/75 cm/100 cm
LED Light Bars Alternative	Herwins	25 cm/75 cm/100 cm (Symphony version are WS2812, check polarity before use, see build. These are very small and are masked with black foil and are thus dimmed, which is great as we can use the full color spectrum of the LEDs and at the same time do not get blind while driving.)

Optional Parts

Part	Count	Source	Comment
Heatsink for Regulators	2	Reichelt	Helps to keep the temperature a little lower
Temperature Sensors	2	Reichelt	Not required but a safety feature
Cooling Fan 30x30	1	Reichelt	Not required but nice to have
Shrinking tube	depends	Amazon	Will help you to have a cleaner and safer build
Fabric tape	depends	Amazon	Will help you to have a cleaner and safer build
3 wire cable	depends	Amazon	you can use this 3 wire cable to connect the LEDs

How to get the signal of the factory build footwell lights without any harm

Part	Count	Source	Comment
electricity thief/T-Connector	2/1	Amazon	to get the car signal
Female Connector	1	Mouser	TE Connectivity / AMP P/N: 1534111-1, car side uses this
Male Connector	1	Mouser	TE Connectivity / AMP P/N: 1-1534155-1, factory build footwell LED’s use this
Retainer / Cover for Connectors	2	Mouser	TE Connectivity / AMP P/N: 1534027-1, each connector needs one
Pin Connectors	4	Mouser	TE Connectivity / AMP P/N: 1-928918-1 (Cut Strip), 2 per plug