BB8_driver.py

#!/usr/bin/python


from bluepy import btle
# import bluetooth
import sys
import struct
import time
import operator
import threading

# These are the message response code that can be return by Sphero.
MRSP = dict(
    ORBOTIX_RSP_CODE_OK=0x00,  # Command succeeded
    ORBOTIX_RSP_CODE_EGEN=0x01,  # General, non-specific error
    ORBOTIX_RSP_CODE_ECHKSUM=0x02,  # Received checksum failure
    ORBOTIX_RSP_CODE_EFRAG=0x03,  # Received command fragment
    ORBOTIX_RSP_CODE_EBAD_CMD=0x04,  # Unknown command ID
    ORBOTIX_RSP_CODE_EUNSUPP=0x05,  # Command currently unsupported
    ORBOTIX_RSP_CODE_EBAD_MSG=0x06,  # Bad message format
    ORBOTIX_RSP_CODE_EPARAM=0x07,  # Parameter value(s) invalid
    ORBOTIX_RSP_CODE_EEXEC=0x08,  # Failed to execute command
    ORBOTIX_RSP_CODE_EBAD_DID=0x09,  # Unknown device ID
    ORBOTIX_RSP_CODE_POWER_NOGOOD=0x31,  # Voltage too low for refash operation
    ORBOTIX_RSP_CODE_PAGE_ILLEGAL=0x32,  # Illegal page number provided
    ORBOTIX_RSP_CODE_FLASH_FAIL=0x33,  # Page did not reprogram correctly
    ORBOTIX_RSP_CODE_MA_CORRUPT=0x34,  # Main application corrupt
    ORBOTIX_RSP_CODE_MSG_TIMEOUT=0x35)  # Msg state machine timed out

# ID codes for asynchronous packets
IDCODE = dict(
    PWR_NOTIFY=chr(0x01),  # Power notifications
    LEVEL1_DIAG=chr(0x02),  # Level 1 Diagnostic response
    DATA_STRM=chr(0x03),  # Sensor data streaming
    CONFIG_BLOCK=chr(0x04),  # Config block contents
    SLEEP=chr(0x05),  # Pre-sleep warning (10 sec)
    MACRO_MARKERS=chr(0x06),  # Macro markers
    COLLISION=chr(0x07))  # Collision detected

RECV = dict(
    ASYNC=[chr(0xff), chr(0xfe)],
    SYNC=[chr(0xff), chr(0xff)])

REQ = dict(
    WITH_RESPONSE=[0xff, 0xff],
    WITHOUT_RESPONSE=[0xff, 0xfe],
    CMD_PING=[0x00, 0x01],
    CMD_VERSION=[0x00, 0x02],
    CMD_SET_BT_NAME=[0x00, 0x10],
    CMD_GET_BT_NAME=[0x00, 0x11],
    CMD_SET_AUTO_RECONNECT=[0x00, 0x12],
    CMD_GET_AUTO_RECONNECT=[0x00, 0x13],
    CMD_GET_PWR_STATE=[0x00, 0x20],
    CMD_SET_PWR_NOTIFY=[0x00, 0x21],
    CMD_SLEEP=[0x00, 0x22],
    CMD_GOTO_BL=[0x00, 0x30],
    CMD_RUN_L1_DIAGS=[0x00, 0x40],
    CMD_RUN_L2_DIAGS=[0x00, 0x41],
    CMD_CLEAR_COUNTERS=[0x00, 0x42],
    CMD_ASSIGN_COUNTER=[0x00, 0x50],
    CMD_POLL_TIMES=[0x00, 0x51],
    CMD_SET_HEADING=[0x02, 0x01],
    CMD_SET_STABILIZ=[0x02, 0x02],
    CMD_SET_ROTATION_RATE=[0x02, 0x03],
    CMD_SET_APP_CONFIG_BLK=[0x02, 0x04],
    CMD_GET_APP_CONFIG_BLK=[0x02, 0x05],
    CMD_SET_DATA_STRM=[0x02, 0x11],
    CMD_CFG_COL_DET=[0x02, 0x12],
    CMD_SET_RGB_LED=[0x02, 0x20],
    CMD_SET_BACK_LED=[0x02, 0x21],
    CMD_GET_RGB_LED=[0x02, 0x22],
    CMD_ROLL=[0x02, 0x30],
    CMD_BOOST=[0x02, 0x31],
    CMD_SET_RAW_MOTORS=[0x02, 0x33],
    CMD_SET_MOTION_TO=[0x02, 0x34],
    CMD_GET_CONFIG_BLK=[0x02, 0x40],
    CMD_SET_DEVICE_MODE=[0x02, 0x42],
    CMD_SET_CFG_BLOCK=[0x02, 0x43],
    CMD_GET_DEVICE_MODE=[0x02, 0x44],
    CMD_RUN_MACRO=[0x02, 0x50],
    CMD_SAVE_TEMP_MACRO=[0x02, 0x51],
    CMD_SAVE_MACRO=[0x02, 0x52],
    CMD_DEL_MACRO=[0x02, 0x53],
    CMD_INIT_MACRO_EXECUTIVE=[0x02, 0x54],
    CMD_ABORT_MACRO=[0x02, 0x55],
    CMD_GET_MACRO_STATUS=[0x02, 0x56],
    CMD_SET_MACRO_STATUS=[0x02, 0x57])

STRM_MASK1 = dict(
    GYRO_H_FILTERED=0x00000001,
    GYRO_M_FILTERED=0x00000002,
    GYRO_L_FILTERED=0x00000004,
    LEFT_EMF_FILTERED=0x00000020,
    RIGHT_EMF_FILTERED=0x00000040,
    MAG_Z_FILTERED=0x00000080,
    MAG_Y_FILTERED=0x00000100,
    MAG_X_FILTERED=0x00000200,
    GYRO_Z_FILTERED=0x00000400,
    GYRO_Y_FILTERED=0x00000800,
    GYRO_X_FILTERED=0x00001000,
    ACCEL_Z_FILTERED=0x00002000,
    ACCEL_Y_FILTERED=0x00004000,
    ACCEL_X_FILTERED=0x00008000,
    IMU_YAW_FILTERED=0x00010000,
    IMU_ROLL_FILTERED=0x00020000,
    IMU_PITCH_FILTERED=0x00040000,
    LEFT_EMF_RAW=0x00200000,
    RIGHT_EMF_RAW=0x00400000,
    MAG_Z_RAW=0x00800000,
    MAG_Y_RAW=0x01000000,
    MAG_X_RAW=0x02000000,
    GYRO_Z_RAW=0x04000000,
    GYRO_Y_RAW=0x08000000,
    GYRO_X_RAW=0x10000000,
    ACCEL_Z_RAW=0x20000000,
    ACCEL_Y_RAW=0x40000000,
    ACCEL_X_RAW=0x80000000)

STRM_MASK2 = dict(
    QUATERNION_Q0=0x80000000,
    QUATERNION_Q1=0x40000000,
    QUATERNION_Q2=0x20000000,
    QUATERNION_Q3=0x10000000,
    ODOM_X=0x08000000,
    ODOM_Y=0x04000000,
    ACCELONE=0x02000000,
    VELOCITY_X=0x01000000,
    VELOCITY_Y=0x00800000)


# The following class adapted from https://gist.github.com/ali1234/5e5758d9c591090291d6

class BTInterface(btle.DefaultDelegate):
    def __init__(self, deviceAddress):
        btle.DefaultDelegate.__init__(self)

        # Address type must be "random" or it won't connect.
        self.peripheral = btle.Peripheral(deviceAddress, btle.ADDR_TYPE_RANDOM)
        self.peripheral.setDelegate(self)

        self.seq = 0

        # Attribute UUIDs are identical to Ollie.
        self.antidos = self.getSpheroCharacteristic('2bbd')
        self.wakecpu = self.getSpheroCharacteristic('2bbf')
        self.txpower = self.getSpheroCharacteristic('2bb2')
        self.roll = self.getSpheroCharacteristic('2ba1')
        self.notify = self.getSpheroCharacteristic('2ba6')

        # This startup sequence is also identical to the one for Ollie.
        # It even uses the same unlock code.
        print 'Sending antidos'
        self.antidos.write('011i3', withResponse=True)
        print 'Sending txpower'
        self.txpower.write('\x0007', withResponse=True)
        print 'Sending wakecpu'
        self.wakecpu.write('\x01', withResponse=True)

    def getSpheroCharacteristic(self, fragment):
        return self.peripheral.getCharacteristics(uuid='22bb746f' + fragment + '75542d6f726568705327')[0]

    def dumpCharacteristics(self):
        for s in self.peripheral.getServices():
            print s
            for c in s.getCharacteristics():
                print c, hex(c.handle)

    def cmd(self, did, cid, data=[], answer=True, resetTimeout=True):
        # Commands are as specified in Sphero API 1.50 PDF.
        # https://github.com/orbotix/DeveloperResources/
        seq = (self.seq & 255)
        self.seq += 1
        sop2 = 0xfc
        sop2 |= 1 if answer else 0
        sop2 |= 2 if resetTimeout else 0
        dlen = len(data) + 1
        chk = (sum(data) + did + cid + seq + dlen) & 255
        chk ^= 255

        msg = [0xff, sop2, did, cid, seq, dlen] + data + [chk]
        print 'cmd:', ' '.join([chr(c).encode('hex') for c in msg])
        # Note: withResponse is very important. Most commands won't work without it.
        self.roll.write(''.join([chr(c) for c in msg]), withResponse=True)

    def send(self, data):
        self.roll.write(data, withResponse=True)

    def handleNotification(self, cHandle, data):
        # print 'Notification:', cHandle, data.encode('hex')
        # print 'BB8 Response:', cHandle,
        Sphero().recv(data)
        # print data
        return data

    def waitForNotifications(self, time):
        self.peripheral.waitForNotifications(time)

    def disconnect(self):
        self.peripheral.disconnect()


# The following code from: https://github.com/mmwise/sphero_ros

# ***********************************************************
# * Software License Agreement (BSD License)
# *
# *  Copyright (c) 2012, Melonee Wise
# *  All rights reserved.
# *
# *  Redistribution and use in source and binary forms, with or without
# *  modification, are permitted provided that the following conditions
# *  are met:
# *
# *   * Redistributions of source code must retain the above copyright
# *     notice, this list of conditions and the following disclaimer.
# *   * Redistributions in binary form must reproduce the above
# *     copyright notice, this list of conditions and the following
# *     disclaimer in the documentation and/or other materials provided
# *     with the distribution.
# *
# *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
# *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
# *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
# *  FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
# *  COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
# *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
# *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
# *  LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
# *  CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
# *  LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
# *  ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# *  POSSIBILITY OF SUCH DAMAGE.
# ***********************************************************
# author: Melonee Wise



class Sphero(threading.Thread):
    def __init__(self, target_name='Sphero'):
        threading.Thread.__init__(self)
        self.target_name = target_name
        self.bt = None
        # Use "sudo hcitool lescan" to find BB8's MAC address input it at deviceAddress = 
        self.deviceAddress = 'DF:79:DD:9C:B6:1D'
        self.shutdown = False
        self.is_connected = False
        self.mask_list = None
        self.stream_mask1 = None
        self.stream_mask2 = None
        self.seq = 0
        self.raw_data_buf = []
        self._communication_lock = threading.Lock()
        self._async_callback_dict = dict()
        self._sync_callback_dict = dict()
        self._sync_callback_queue = []

    def connect(self):
        self.bt = BTInterface(self.deviceAddress)
        # self.is_connected = self.bt.connect()
        self.is_connected = True
        return True

    def inc_seq(self):
        self.seq = self.seq + 1
        if self.seq > 0xff:
            self.seq = 0

    def pack_cmd(self, req, cmd):
        self.inc_seq()
        #   print req + [self.seq] + [len(cmd)+1] + cmd
        return req + [self.seq] + [len(cmd) + 1] + cmd

    def data2hexstr(self, data):
        return ' '.join([("%02x" % ord(d)) for d in data])

    def create_mask_list(self, mask1, mask2):
        # save the mask
        sorted_STRM1 = sorted(STRM_MASK1.iteritems(), key=operator.itemgetter(1), reverse=True)
        # create a list containing the keys that are part of the mask
        self.mask_list1 = [key for key, value in sorted_STRM1 if value & mask1]

        sorted_STRM2 = sorted(STRM_MASK2.iteritems(), key=operator.itemgetter(1), reverse=True)
        # create a list containing the keys that are part of the mask
        self.mask_list2 = [key for key, value in sorted_STRM2 if value & mask2]
        self.mask_list = self.mask_list1 + self.mask_list2

    def add_async_callback(self, callback_type, callback):
        self._async_callback_dict[callback_type] = callback

    def remove_async_callback(self, callback_type):
        del self._async_callback_dict[callback_type]

    def add_sync_callback(self, callback_type, callback):
        self._sync_callback_dict[callback_type] = callback

    def remove_sync_callback(self, callback_type):
        del self._sync_callback_dict[callback_type]

    def clamp(self, n, minn, maxn):
        return max(min(maxn, n), minn)

    def ping(self, response):
        """
        The Ping command is used to verify both a solid data link with the
        Client and that Sphero is awake and dispatching commands.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_PING'], []), response)

    def get_version(self, response):
        """
        The Get Versioning command returns a whole slew of software and
        hardware information.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_VERSION'], []), response)

    def set_device_name(self, name, response):
        """
        This assigned name is held internally and produced as part of the
        Get Bluetooth Info service below. Names are clipped at 48
        characters in length to support UTF-8 sequences; you can send
        something longer but the extra will be discarded. This field
        defaults to the Bluetooth advertising name.

        :param name: 48 character name.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_BT_NAME'], [name]), response)

    def get_bt_name(self, response):
        """
        This returns the textual name (in ASCII) that the Bluetooth module
        advertises. It also returns the BTA Bluetooth Address or MAC ID
        for this device. Both values are returned in ASCII and have field
        widths of 16 characters, with unused trailing characters set to
        00h.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_GET_BT_NAME'], []), response)

    def set_auto_reconnect(self, enable, time, response):
        """
        This configures the control of the Bluetooth module in its attempt
        to automatically reconnect with the last iPhone device. This is a
        courtesy behavior since the iPhone Bluetooth stack doesn't initiate
        automatic reconnection on its own.  The two parameters are simple:
        flag = 00h to disable or 01h to enable, and time = the number of
        seconds after power-up in which to enable auto reconnect mode. For
        example, if time = 30 then the module will be attempt reconnecting 30
        seconds after waking up.

        :param enable: 00h to disable or 01h to enable auto reconnecting.
        :param time: the number of seconds after power-up in which to\
        enable auto reconnect mode
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_AUTO_RECONNECT'], [enable, time]), response)

    def get_auto_reconnect(self, response):
        """
        This returns the Bluetooth auto reconnect values as defined in the
        Set Auto Reconnect command.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_GET_AUTO_RECONNECT'], []), response)

    def get_power_state(self, response):
        """
        This returns the current power state and some additional
        parameters to the Client.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_GET_PWR_STATE'], []), response)

    def set_power_notify(self, enable, response):
        """
        This enables Sphero to asynchronously notify the Client
        periodically with the power state or immediately when the power
        manager detects a state change. Timed notifications arrive every 10
        seconds until they're explicitly disabled or Sphero is unpaired. The
        flag is as you would expect, 00h to disable and 01h to enable.

        :param enable: 00h to disable and 01h to enable power notifications.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_PWR_NOTIFY'], [enable]), response)

    def go_to_sleep(self, time, macro, response):
        """
        This puts Sphero to sleep immediately with two parameters: the
        first is the number of seconds after which it will automatically
        re-awaken. If set to zero, this feature is disabled. If non-zero then
        the MACRO parameter allows an optional system macro to be run upon
        wakeup. If this is set to zero, no macro is executed.

        :param time: number of seconds wait before auto re-awake.
        :param macro: macro number to run when re-awakened.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SLEEP'], [(time >> 8), (time & 0xff), macro]), response)

    def run_l1_diags(self, response):
        """
        This is a developer-level command to help diagnose aberrant
        behavior. Most system counters, process flags, and system states
        are decoded into human readable ASCII. There are two responses to
        this command: a Simple Response followed by a large async message
        containing the results of the diagnostic tests.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_RUN_L1_DIAGS'], []), response)

    def run_l2_diags(self, response):
        """
        This is a developers-only command to help diagnose aberrant
        behavior. It is much less impactful than the Level 1 command as it
        doesn't interfere with the current operation it simply returns a
        current set of statistics to the client.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_RUN_L2_DIAGS'], []), response)

    def clear_counters(self, response):
        """
        This is a developers-only command to clear the various system
        counters described in the level 2 diag.

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_CLEAR_COUNTERS'], []), response)

    def assign_counter_value(self, counter, response):
        """
        Sphero contains a 32-bit counter that increments every millisecond
        when it's not in the Idle state. It has no absolute meaning and is
        reset for various reasons. This command assigns the counter a
        specific value for subsequent sampling.

        :param counter: value to set the counter to.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_ASSIGN_COUNTER'],
                                [((counter >> 24) & 0xff), ((counter >> 16) & 0xff), ((counter >> 8) & 0xff),
                                 (counter & 0xff)]), response)

    def poll_packet_times(self, time, response):
        """
        This command helps the Client application profile the transmission
        and processing latencies in Sphero so that a relative
        synchronization of timebases can be performed. It allows the
        Client to reconcile time stamped messages from Sphero to its own
        time stamped events.

        The scheme is as follows: the Client sends the command with the
        Client Tx time (:math:`T_{1}`) filled in. Upon receipt of the packet, the
        command processor in Sphero copies that time into the response
        packet and places the current value of the millisecond counter
        into the Sphero Rx time field (:math:`T_{2}`). Just before the transmit
        engine streams it into the Bluetooth module, the Sphero Tx time
        value (:math:`T_{3}`)  is filled in. If the Client then records the time at
        which the response is received (:math:`T_{4}`) the relevant time segments can
        be computed from the four time stamps (:math:`T_{1}, T_{2}, T_{3}, T_{4}`):

        * The value offset represents the maximum-likelihood time offset\
          of the Client clock to Sphero's system clock.
            * offset :math:`= 1/2*[(T_{2} - T_{1}) + (T_{3}  - T_{4})]`

        * The value delay represents the round-trip delay between the\
          Client and Sphero:
            * delay :math:`= (T_{4} - T_{1}) - (T_{3} - T_{2})`

        :param time: client Tx time.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_POLL_TIME'],
                                [((time >> 24) & 0xff), ((time >> 16) & 0xff), ((time >> 8) & 0xff), (time & 0xff)]),
                  response)

    def set_heading(self, heading, response):
        """
        This allows the client to adjust the orientation of Sphero by
        commanding a new reference heading in degrees, which ranges from 0
        to 359. You will see the ball respond immediately to this command
        if stabilization is enabled.

        :param heading: heading in degrees from 0 to 359 (motion will be\
        shortest angular distance to heading command)
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_HEADING'], [(heading >> 8), (heading & 0xff)]), response)

    def set_stablization(self, enable, response):
        """
        This turns on or off the internal stabilization of Sphero, in
        which the IMU is used to match the ball's orientation to its
        various set points. The flag value is as you would expect, 00h for
        off and 01h for on.

        :param enable: 00h for off and 01h for on (on by default).
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_STABILIZ'], [enable]), response)

    def set_rotation_rate(self, rate, response):
        """
        This allows you to control the rotation rate that Sphero will use
        to meet new heading commands. The commanded value is in units of
        0.784 degrees/sec. So, setting a value of c8h will set the
        rotation rate to 157 degrees/sec. A value of 255 jumps to the
        maximum and a value of 1 is the minimum.

        :param rate: rotation rate in units of 0.784degrees/sec (setting\
        this value will not cause the device to move only set the rate it\
        will move in other funcation calls).
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_ROTATION_RATE'], [self.clamp(rate, 0, 255)]), response)

    def set_app_config_blk(self, app_data, response):
        """
        This allows you to write a 32 byte block of data from the
        configuration block that is set aside for exclusive use by
        applications.

        :param app_data: block set aside for application.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_APP_CONFIG_BLK'],
                                [((app_data >> 24) & 0xff), ((app_data >> 16) & 0xff), ((app_data >> 8) & 0xff),
                                 (app_data & 0xff)]), response)

    def get_app_config_blk(self, response):
        """
        This allows you to retrieve the application configuration block\
        that is set aside for exclusive use by applications.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_GET_APP_CONFIG_BLK'], []), response)

    def set_data_strm(self, sample_div, sample_frames, sample_mask1, pcnt, sample_mask2, response):
        """
        Currently the control system runs at 400Hz and because it's pretty
        unlikely you will want to see data at that rate, N allows you to
        divide that down. sample_div = 2 yields data samples at 200Hz,
        sample_div = 10, 40Hz, etc. Every data sample consists of a
        "frame" made up of the individual sensor values as defined by the
        sample_mask. The sample_frames value defines how many frames to
        collect in memory before the packet is emitted. In this sense, it
        controls the latency of the data you receive. Increasing
        sample_div and the number of bits set in sample_mask drive the
        required throughput. You should experiment with different values
        of sample_div, sample_frames and sample_mask to see what works
        best for you.

        :param sample_div: divisor of the maximum sensor sampling rate.
        :param sample_frames: number of sample frames emitted per packet.
        :param sample_mask1: bitwise selector of data sources to stream.
        :param pcnt: packet count (set to 0 for unlimited streaming).
        :param response: request response back from Sphero.
        """
        data = self.pack_cmd(REQ['CMD_SET_DATA_STRM'], \
                             [(sample_div >> 8), (sample_div & 0xff), (sample_frames >> 8), (sample_frames & 0xff),
                              ((sample_mask1 >> 24) & 0xff), \
                              ((sample_mask1 >> 16) & 0xff), ((sample_mask1 >> 8) & 0xff), (sample_mask1 & 0xff), pcnt,
                              ((sample_mask2 >> 24) & 0xff), \
                              ((sample_mask2 >> 16) & 0xff), ((sample_mask2 >> 8) & 0xff), (sample_mask2 & 0xff)])
        self.create_mask_list(sample_mask1, sample_mask2)
        self.stream_mask1 = sample_mask1
        self.stream_mask2 = sample_mask2
        print data
        self.send(data, response)

    def set_filtered_data_strm(self, sample_div, sample_frames, pcnt, response):
        """
        Helper function to add all the filtered data to the data strm
        mask, so that the user doesn't have to set the data strm manually.

        :param sample_div: divisor of the maximum sensor sampling rate.
        :param sample_frames: number of sample frames emitted per packet.
        :param pcnt: packet count (set to 0 for unlimited streaming).
        :param response: request response back from Sphero.
        """
        mask1 = 0
        mask2 = 0
        for key, value in STRM_MASK1.iteritems():
            if 'FILTERED' in key:
                mask1 = mask1 | value
        for value in STRM_MASK2.itervalues():
            mask2 = mask2 | value
        self.set_data_strm(sample_div, sample_frames, mask1, pcnt, mask2, response)

    def set_raw_data_strm(self, sample_div, sample_frames, pcnt, response):
        """
        Helper function to add all the raw data to the data strm mask, so
        that the user doesn't have to set the data strm manually.

        :param sample_div: divisor of the maximum sensor sampling rate.
        :param sample_frames: number of sample frames emitted per packet.
        :param pcnt: packet count (set to 0 for unlimited streaming).
        :param response: request response back from Sphero.
        """
        mask1 = 0
        mask2 = 0
        for key, value in STRM_MASK1.iteritems():
            if 'RAW' in key:
                mask1 = mask1 | value
        for value in STRM_MASK2.itervalues():
            mask2 = mask2 | value
        self.set_data_strm(sample_div, sample_frames, mask1, pcnt, mask2, response)

    def set_all_data_strm(self, sample_div, sample_frames, pcnt, response):
        """
        Helper function to add all the data to the data strm mask, so
        that the user doesn't have to set the data strm manually.

        :param sample_div: divisor of the maximum sensor sampling rate.
        :param sample_frames: number of sample frames emitted per packet.
        :param pcnt: packet count (set to 0 for unlimited streaming).
        :param response: request response back from Sphero.
        """
        mask1 = 0
        mask2 = 0
        for value in STRM_MASK1.itervalues():
            mask1 = mask1 | value
        for value in STRM_MASK2.itervalues():
            mask2 = mask2 | value
        self.set_data_strm(sample_div, sample_frames, mask1, pcnt, mask2, response)

    def config_collision_detect(self, method, Xt, Xspd, Yt, Yspd, ignore_time, response):
        """
        This command either enables or disables asynchronous message
        generation when a collision is detected.The Ignore Time parameter
        disables collision detection for a period of time after the async
        message is generated, preventing message overload to the
        client. The value is in 10 millisecond increments.

        :param method: Detection method type to use. Currently the only\
        method supported is 01h. Use 00h to completely disable this\
        service.
        :param Xt, Yt: An 8-bit settable threshold for the X (left/right)\
        and Y (front/back) axes of Sphero. A value of 00h disables the\
        contribution of that axis.
        :param Xspd,Yspd: An 8-bit settable speed value for the X and Y\
        axes. This setting is ranged by the speed, then added to Xt, Yt to\
        generate the final threshold value.
        :param ignore_time: An 8-bit post-collision dead time to prevent\
        retriggering; specified in 10ms increments.
        """
        self.send(self.pack_cmd(REQ['CMD_CFG_COL_DET'], [method, Xt, Xspd, Yt, Yspd, ignore_time]), response)

    def set_rgb_led(self, red, green, blue, save, response):
        """
        This allows you to set the RGB LED color. The composite value is
        stored as the "application LED color" and immediately driven to
        the LED (if not overridden by a macro or orbBasic operation). If
        FLAG is true, the value is also saved as the "user LED color"
        which persists across power cycles and is rendered in the gap
        between an application connecting and sending this command.

        :param red: red color value.
        :param green: green color value.
        :param blue: blue color value.
        :param save: 01h for save (color is saved as "user LED color").
        """
        self.send(self.pack_cmd(REQ['CMD_SET_RGB_LED'],
                                [self.clamp(red, 0, 255), self.clamp(green, 0, 255), self.clamp(blue, 0, 255), save]),
                  response)

    def set_back_led(self, brightness, response):
        """
        This allows you to control the brightness of the back LED. The
        value does not persist across power cycles.

        :param brightness: 0-255, off-on (the blue LED on hemisphere of the Sphero).
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_SET_BACK_LED'], [self.clamp(brightness, 0, 255)]), response)

    def get_rgb_led(self, response):
        """
        This retrieves the "user LED color" which is stored in the config
        block (which may or may not be actively driven to the RGB LED).

        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_GET_RGB_LED'], []), response)

    def roll(self, speed, heading, state, response):
        """
        This commands Sphero to roll along the provided vector. Both a
        speed and a heading are required; the latter is considered
        relative to the last calibrated direction. A state Boolean is also
        provided (on or off). The client convention for heading follows the 360
        degrees on a circle, relative to the ball: 0 is straight ahead, 90
        is to the right, 180 is back and 270 is to the left. The valid
        range is 0..359.

        :param speed: 0-255 value representing 0-max speed of the sphero.
        :param heading: heading in degrees from 0 to 359.
        :param state: 00h for off (braking) and 01h for on (driving).
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_ROLL'], [self.clamp(speed, 0, 255), (heading >> 8), (heading & 0xff), state]),
                  response)

    def boost(self, time, heading, response):
        """
        This commands Sphero to meet the provided heading, disable
        stabilization and ramp the motors up to full-speed for a period of
        time. The Time parameter is the duration in tenths of a
        second. Setting it to zero enables constant boost until a Set
        Stabilization command is received.

        :param time: duration of boost in tenths of seconds.
        :param heading: the heading to travel while boosting.
        :param response: request response back from Sphero.
        """
        self.send(self.pack_cmd(REQ['CMD_BOOST'], [time, (heading >> 8), (heading & 0xff)]), response)

    def set_raw_motor_values(self, l_mode, l_power, r_mode, r_power, response):
        """
        This allows you to take over one or both of the motor output
        values, instead of having the stabilization system control
        them. Each motor (left and right) requires a mode (see below) and
        a power value from 0- 255. This command will disable stabilization
        if both modes aren't "ignore" so you'll need to re-enable it via
        CID 02h once you're done.

        :param mode: 0x00 - off, 0x01 - forward, 0x02 - reverse, 0x03 -\
        brake, 0x04 - ignored.
        :param power: 0-255 scalar value (units?).
        """
        self.send(self.pack_cmd(REQ['CMD_RAW_MOTORS'], [l_mode, l_power, r_mode, r_power]), response)

    def send(self, data, response):
        """
        Packets are sent from Client -> Sphero in the following byte format::

          -------------------------------------------------------
          | SOP1 | SOP2 | DID | CID | SEQ | DLEN | <data> | CHK |
          -------------------------------------------------------

        * SOP1 - start packet 1 - Always 0xff.
        * SOP2 - start packet 2 - Set to 0xff when an acknowledgement is\
          expected, 0xfe otherwise.
        * DID - Device ID
        * CID - Command ID
        * SEQ - Sequence Number - This client field is echoed in the\
          response for all synchronous commands (and ignored by Sphero\
          when SOP2 = 0xfe)
        * DLEN - Data
        * Length - Number of bytes through the end of the packet.
        * <data>
        * CHK - Checksum - The modulo 256 sum of all the bytes from the\
          DID through the end of the data payload, bit inverted (1's\
          complement).
        """
        # compute the checksum
        # modulo 256 sum of data bit inverted
        checksum = ~ sum(data) % 256
        # if expecting response back from the sphero
        if response:
            output = REQ['WITH_RESPONSE'] + data + [checksum]
        else:
            output = REQ['WITHOUT_RESPONSE'] + data + [checksum]
        # pack the msg
        msg = ''.join(struct.pack('B', x) for x in output)
        # send the msg
        with self._communication_lock:
            self.bt.send(msg)

    def run(self):
        # this is larger than any single packet
        self.recv(1024)

    def recv(self, num_bytes):
        '''
        Commands are acknowledged from the Sphero -> Client in the
        following format::

          -------------------------------------------------
          |SOP1 | SOP2 | MSRP | SEQ | DLEN | <data> | CHK |
          -------------------------------------------------

        * SOP1 - Start Packet 1 - Always 0xff.
        * SOP2 - Start Packet 2 - Set to 0xff when this is an\
          acknowledgement, 0xfe otherwise.
        * MSRP - Message Response - This is generated by the message\
          decoder of the virtual device.
        * SEQ - Sequence Number - Echoed to the client when this is a\
          direct message response (set to 00h when SOP2 = FEh)
        * DLEN - Data Length - The number of bytes following through the\
          end of the packet
        * <data>
        * CHK - Checksum - - The modulo 256 sum of all the bytes from the\
          DID through the end of the data payload, bit inverted (1's\
          complement)

        Asynchronous Packets are sent from Sphero -> Client in the
        following byte format::

          -------------------------------------------------------------
          |SOP1 | SOP2 | ID CODE | DLEN-MSB | DLEN-LSB | <data> | CHK |
          -------------------------------------------------------------

        * SOP1 - Start Packet 1 - Always 0xff.
        * SOP2 - Start Packet 2 - Set to 0xff when this is an
          acknowledgement, 0xfe otherwise.
        * ID CODE - ID Code - See the IDCODE dict
        * DLEN-MSB - Data Length MSB - The MSB number of bytes following\
          through the end of the packet
        * DLEN-LSB - Data Length LSB - The LSB number of bytes following\
          through the end of the packet
        * <data>
        * CHK - Checksum - - The modulo 256 sum of all the bytes from the\
          DID through the end of the data payload, bit inverted (1's\
          complement)

        '''

        data = self.raw_data_buf
        while len(data) > 5:
            if data[:2] == RECV['SYNC']:
                print "got response packet"
                # response packet
                data_length = ord(data[4])
                if data_length + 5 <= len(data):
                    data_packet = data[:(5 + data_length)]
                    data = data[(5 + data_length):]
                else:
                    break
                    # print "Response packet", self.data2hexstr(data_packet)

            elif data[:2] == RECV['ASYNC']:
                data_length = (ord(data[3]) << 8) + ord(data[4])
                if data_length + 5 <= len(data):
                    data_packet = data[:(5 + data_length)]
                    data = data[(5 + data_length):]
                else:
                    # the remainder of the packet isn't long enough
                    break
                if data_packet[2] == IDCODE['DATA_STRM'] and self._async_callback_dict.has_key(IDCODE['DATA_STRM']):
                    self._async_callback_dict[IDCODE['DATA_STRM']](self.parse_data_strm(data_packet, data_length))
                elif data_packet[2] == IDCODE['COLLISION'] and self._async_callback_dict.has_key(
                        IDCODE['COLLISION']):
                    self._async_callback_dict[IDCODE['COLLISION']](
                        self.parse_collision_detect(data_packet, data_length))
                elif data_packet[2] == IDCODE['PWR_NOTIFY'] and self._async_callback_dict.has_key(
                        IDCODE['PWR_NOTIFY']):
                    self._async_callback_dict[IDCODE['PWR_NOTIFY']](self.parse_pwr_notify(data_packet, data_length))
                else:
                    print "got a packet that isn't streaming"
            else:
                raise RuntimeError("Bad SOF : " + self.data2hexstr(data))
        self.raw_data_buf = data


    def parse_pwr_notify(self, data, data_length):
        '''
        The data payload of the async message is 1h bytes long and
        formatted as follows::
    
          --------
          |State |
          --------
    
        The power state byte:
          * 01h = Battery Charging,
          * 02h = Battery OK,
          * 03h = Battery Low,
          * 04h = Battery Critical
        '''
        return struct.unpack_from('B', ''.join(data[5:]))[0]


    def parse_collision_detect(self, data, data_length):
        '''
        The data payload of the async message is 10h bytes long and
        formatted as follows::
    
          -----------------------------------------------------------------
          |X | Y | Z | AXIS | xMagnitude | yMagnitude | Speed | Timestamp |
          -----------------------------------------------------------------
    
        * X, Y, Z - Impact components normalized as a signed 16-bit\
        value. Use these to determine the direction of collision event. If\
        you don't require this level of fidelity, the two Magnitude fields\
        encapsulate the same data in pre-processed format.
        * Axis - This bitfield specifies which axes had their trigger\
        thresholds exceeded to generate the event. Bit 0 (01h) signifies\
        the X axis and bit 1 (02h) the Y axis.
        * xMagnitude - This is the power that crossed the programming\
        threshold Xt + Xs.
        * yMagnitude - This is the power that crossed the programming\
        threshold Yt + Ys.
        * Speed - The speed of Sphero when the impact was detected.
        * Timestamp - The millisecond timer value at the time of impact;\
        refer to the documentation of CID 50h and 51h to make sense of\
        this value.
        '''
        output = {}
    
        output['X'], output['Y'], output['Z'], output['Axis'], output['xMagnitude'], output['yMagnitude'], output[
            'Speed'], output['Timestamp'] = struct.unpack_from('>hhhbhhbI', ''.join(data[5:]))
        return output


    def parse_data_strm(self, data, data_length):
        output = {}
        for i in range((data_length - 1) / 2):
            unpack = struct.unpack_from('>h', ''.join(data[5 + 2 * i:]))
            output[self.mask_list[i]] = unpack[0]
        print self.mask_list
        print output
        return output


    def disconnect(self):
        self.is_connected = False
        #self.bt.disconnect()
        self.bt.peripheral.disconnect()
        return self.is_connected