From 62d6bc3bee300a69758776517418286ac704c82a Mon Sep 17 00:00:00 2001 From: TuTu-GB <1827977214@qq.com> Date: Tue, 22 Oct 2024 10:27:36 +0800 Subject: [PATCH] Update User_Setup.h --- User_Setup.h | 218 +++++++++++++++++++++++++-------------------------- 1 file changed, 109 insertions(+), 109 deletions(-) diff --git a/User_Setup.h b/User_Setup.h index a0123318..8f8b0c10 100644 --- a/User_Setup.h +++ b/User_Setup.h @@ -1,111 +1,111 @@ -// USER DEFINED SETTINGS -// Set driver type, fonts to be loaded, pins used and SPI control method etc. +// 用户定义的设置 +// 设置驱动类型、要加载的字体、使用的引脚、SPI控制方式等 // -// See the User_Setup_Select.h file if you wish to be able to define multiple -// setups and then easily select which setup file is used by the compiler. +// 如果您希望能够定义多个，请参阅 User_Setup_Select.h 文件 +// 设置，然后轻松选择编译器使用哪个设置文件。 // -// If this file is edited correctly then all the library example sketches should -// run without the need to make any more changes for a particular hardware setup! -// Note that some sketches are designed for a particular TFT pixel width/height +// 如果该文件编辑正确，那么所有库示例草图都应该 +// 运行时消耗特定对硬件设置进行更多更改！ +// 请注意，一些草图是针对特定TFT宽度/高度而设计的 -// User defined information reported by "Read_User_Setup" test & diagnostics example -#define USER_SETUP_INFO "User_Setup" +//“Read_User_Setup”测试和诊断样本报告的用户定义信息 +#define USER_SETUP_INFO“用户设置” -// Define to disable all #warnings in library (can be put in User_Setup_Select.h) -//#define DISABLE_ALL_LIBRARY_WARNINGS +//定义取消库中的所有#warnings（可以放在User_Setup_Select.h中） +//#定义DISABLE_ALL_LIBRARY_WARNINGS -// ################################################################################## +// ################################################## #################################################### // -// Section 1. Call up the right driver file and any options for it +// 第 1 部分。调用正确的驱动程序文件及其任何选项 // -// ################################################################################## - -// Define STM32 to invoke optimised processor support (only for STM32) -//#define STM32 - -// Defining the STM32 board allows the library to optimise the performance -// for UNO compatible "MCUfriend" style shields -//#define NUCLEO_64_TFT -//#define NUCLEO_144_TFT - -// STM32 8-bit parallel only: -// If STN32 Port A or B pins 0-7 are used for 8-bit parallel data bus bits 0-7 -// then this will improve rendering performance by a factor of ~8x -//#define STM_PORTA_DATA_BUS -//#define STM_PORTB_DATA_BUS - -// Tell the library to use parallel mode (otherwise SPI is assumed) -//#define TFT_PARALLEL_8_BIT -//#defined TFT_PARALLEL_16_BIT // **** 16-bit parallel ONLY for RP2040 processor **** - -// Display type - only define if RPi display -//#define RPI_DISPLAY_TYPE // 20MHz maximum SPI - -// Only define one driver, the other ones must be commented out -#define ILI9341_DRIVER // Generic driver for common displays -//#define ILI9341_2_DRIVER // Alternative ILI9341 driver, see https://github.com/Bodmer/TFT_eSPI/issues/1172 -//#define ST7735_DRIVER // Define additional parameters below for this display -//#define ILI9163_DRIVER // Define additional parameters below for this display -//#define S6D02A1_DRIVER -//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI -//#define HX8357D_DRIVER -//#define ILI9481_DRIVER -//#define ILI9486_DRIVER -//#define ILI9488_DRIVER // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high) -//#define ST7789_DRIVER // Full configuration option, define additional parameters below for this display -//#define ST7789_2_DRIVER // Minimal configuration option, define additional parameters below for this display -//#define R61581_DRIVER -//#define RM68140_DRIVER -//#define ST7796_DRIVER -//#define SSD1351_DRIVER -//#define SSD1963_480_DRIVER -//#define SSD1963_800_DRIVER -//#define SSD1963_800ALT_DRIVER -//#define ILI9225_DRIVER -//#define GC9A01_DRIVER - -// Some displays support SPI reads via the MISO pin, other displays have a single -// bi-directional SDA pin and the library will try to read this via the MOSI line. -// To use the SDA line for reading data from the TFT uncomment the following line: - -// #define TFT_SDA_READ // This option is for ESP32 ONLY, tested with ST7789 and GC9A01 display only - -// For ST7735, ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display -// Try ONE option at a time to find the correct colour order for your display - -// #define TFT_RGB_ORDER TFT_RGB // Colour order Red-Green-Blue -// #define TFT_RGB_ORDER TFT_BGR // Colour order Blue-Green-Red - -// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below - -// #define M5STACK - -// For ST7789, ST7735, ILI9163 and GC9A01 ONLY, define the pixel width and height in portrait orientation -// #define TFT_WIDTH 80 -// #define TFT_WIDTH 128 -// #define TFT_WIDTH 172 // ST7789 172 x 320 -// #define TFT_WIDTH 170 // ST7789 170 x 320 -// #define TFT_WIDTH 240 // ST7789 240 x 240 and 240 x 320 -// #define TFT_HEIGHT 160 -// #define TFT_HEIGHT 128 +// ################################################## #################################################### + +//定义STM32调用优化的处理器支持（仅适用于STM32） +//#定义STM32 + +//定义STM32板允许库优化性能 +// 用于UNO兼容的“MCUfriend”风格防护罩 +//#定义NUCLEO_64_TFT +//#定义NUCLEO_144_TFT + +//仅STM32 8位家具： +//如果STN32端口A或B引脚0-7用于8位设备数据占用位0-7 +//现在这个渲染性能提升约8倍 +//#定义STM_PORTA_DATA_BUS +//#定义STM_PORTB_DATA_BUS + +// 告诉库使用并行模式（否则假定为 SPI） +//#定义TFT_PARALLEL_8_BIT +//#define TFT_PARALLEL_16_BIT // **** 16位主板仅适用于RP2040处理器 **** + +// 显示类型 - 仅定义 RPi 是否显示 +//#define RPI_DISPLAY_TYPE // 20MHz 最大 SPI + +// 只定义一个驱动，其他的必须注释掉 +#define ILI9341_DRIVER // 通用驱动器的通用驱动程序 +//#define ILI9341_2_DRIVER //替代ILI9341驱动程序，请参考https://github.com/Bodmer/TFT_eSPI/issues/1172 +//#define ST7735_DRIVER //用于显示器定义以下附加参数 +//#define ILI9163_DRIVER //用于显示器定义以下附加参数 +//#定义S6D02A1_DRIVER +//#define RPI_ILI9486_DRIVER //最大20MHz SPI +//#定义HX8357D_DRIVER +//#定义ILI9481_DRIVER +//#定义ILI9486_DRIVER +//#define ILI9488_DRIVER // 警告：如果其他设备共享 SPI 中断，请勿将 ILI9488 显示 SDO 连接到 MISO（当 CS 为高电平时，TFT SDO 不会进入三态） +//#define ST7789_DRIVER // 完整配置选项，为显卡定义以下附加参数 +//#define ST7789_2_DRIVER //配置最小选项，为此显示器定义以下附加参数 +//#定义R61581_DRIVER +//#定义 RM68140_DRIVER +//#定义ST7796_DRIVER +//#定义SSD1351_DRIVER +//#定义SSD1963_480_DRIVER +//#定义SSD1963_800_DRIVER +//#定义SSD1963_800ALT_DRIVER +//#定义ILI9225_DRIVER +//#定义GC9A01_DRIVER + +// 有些放大器支持通过MISO引脚进行SPI读取，其他放大器则只有一个 +//三个SDA引脚，库将尝试通过MOSI线读取该引脚。 +//要使用SDA线从TFT读取数据，请取消以下注释行： + +// #define TFT_SDA_READ 该 // 选项仅适用于 ESP32，仅使用 ST7789 和 GC9A01 显示器进行测试 + +// 仅适用于 ST7735、ST7789 和 ILI9341，如果在显示器上交换机上为蓝色和红色，请定义颜色顺序 +//您再次尝试一个选项，找到适合显示器的正确颜色顺序 + +// #define TFT_RGB_ORDER TFT_RGB // 颜色顺序红-绿-蓝 +// #define TFT_RGB_ORDER TFT_BGR // 颜色顺序蓝-绿-红 + +// 仅适用于集成 ILI9341 显示屏的 M5Stack ESP32 模块，删除下面一行中的 // + +//#定义M5STACK + +// 仅适用于 ST7789、ST7735、ILI9163 和 GC9A01，定义纵向像素宽度和高度 +//#定义TFT_WIDTH 80 +//#定义TFT_WIDTH 128 +// #define TFT_WIDTH 172 // ST7789 172 x 320 +// #define TFT_WIDTH 170 // ST7789 170 x 320 +// #define TFT_WIDTH 240 // ST7789 240 x 240 和 240 x 320 +// #定义 TFT_HEIGHT 160 +//#定义TFT_HEIGHT 128 // #define TFT_HEIGHT 240 // ST7789 240 x 240 // #define TFT_HEIGHT 320 // ST7789 240 x 320 // #define TFT_HEIGHT 240 // GC9A01 240 x 240 -// For ST7735 ONLY, define the type of display, originally this was based on the -// colour of the tab on the screen protector film but this is not always true, so try -// out the different options below if the screen does not display graphics correctly, -// e.g. colours wrong, mirror images, or stray pixels at the edges. -// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this -// this User_Setup file, then rebuild and upload the sketch to the board again: - -// #define ST7735_INITB -// #define ST7735_GREENTAB -// #define ST7735_GREENTAB2 -// #define ST7735_GREENTAB3 -// #define ST7735_GREENTAB128 // For 128 x 128 display -// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset) -// #define ST7735_ROBOTLCD // For some RobotLCD Arduino shields (128x160, BGR, https://docs.arduino.cc/retired/getting-started-guides/TFT) +// 仅适用于 ST7735，定义显示类型，最初这是基于 +// 屏幕保护膜上标签的颜色，但这并不总是正确的，所以请尝试 +// 如果屏幕不能正确显示图形，则退出下面的不同选项， +// 例如，颜色错误、镜像或边缘出现杂散像素。 +// 对于 ST7735 显示驱动程序，注释掉除其中一个选项之外的所有选项，保存此选项 +// 这个 User_Setup 文件，然后重新构建草图并将其上传到开发板： + +//#定义ST7735_INITB +//#定义ST7735_GREENTAB +//#定义ST7735_GREENTAB2 +//#定义ST7735_GREENTAB3 +// #define ST7735_GREENTAB128 // 对于 128 x 128 显示 +// #define ST7735_GREENTAB160x80 /​​/ 用于 160 x 80 显示（BGR、反转、26 偏移） +// #define ST7735_ROBOTLCD // 对于一些 RobotLCD Arduino 扩展板（128x160，BGR，https://docs.arduino.cc/retired/getting-started-guides/TFT） // #define ST7735_REDTAB // #define ST7735_BLACKTAB // #define ST7735_REDTAB160x80 // For 160 x 80 display with 24 pixel offset @@ -167,13 +167,13 @@ // ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ###### // For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation -#define TFT_MISO PIN_D6 // Automatically assigned with ESP8266 if not defined -#define TFT_MOSI PIN_D7 // Automatically assigned with ESP8266 if not defined -#define TFT_SCLK PIN_D5 // Automatically assigned with ESP8266 if not defined +//#define TFT_MISO PIN_D6 // Automatically assigned with ESP8266 if not defined +//#define TFT_MOSI PIN_D7 // Automatically assigned with ESP8266 if not defined +//#define TFT_SCLK PIN_D5 // Automatically assigned with ESP8266 if not defined -#define TFT_CS PIN_D8 // Chip select control pin D8 -#define TFT_DC PIN_D3 // Data Command control pin -#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line) +//#define TFT_CS PIN_D8 // Chip select control pin D8 +//#define TFT_DC PIN_D3 // Data Command control pin +//#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line) //#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V @@ -209,12 +209,12 @@ // For ESP32 Dev board (only tested with ILI9341 display) // The hardware SPI can be mapped to any pins -//#define TFT_MISO 19 -//#define TFT_MOSI 23 -//#define TFT_SCLK 18 -//#define TFT_CS 15 // Chip select control pin -//#define TFT_DC 2 // Data Command control pin -//#define TFT_RST 4 // Reset pin (could connect to RST pin) +#define TFT_MISO 19 +#define TFT_MOSI 23 +#define TFT_SCLK 18 +#define TFT_CS 15 // Chip select control pin +#define TFT_DC 2 // Data Command control pin +#define TFT_RST 4 // Reset pin (could connect to RST pin) //#define TFT_RST -1 // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST // For ESP32 Dev board (only tested with GC9A01 display)