diff --git a/docs/Knowledge_Base/Home_Lab/Portainer_Docker.md b/docs/Knowledge_Base/Home_Lab/Portainer_Docker.md
index ff2f00fa5..f172cf7da 100644
--- a/docs/Knowledge_Base/Home_Lab/Portainer_Docker.md
+++ b/docs/Knowledge_Base/Home_Lab/Portainer_Docker.md
@@ -22,9 +22,9 @@
     docker ps
     ```
 
-    Log in https://localhost:9443
+    Log in [https://localhost:9443](https://localhost:9443)
     
-    Sources: [Docker Linux Install CE](https://docs.portainer.io/start/install-ce/server/docker/linux)
+    **Sources**: [Docker Linux Install CE](https://docs.portainer.io/start/install-ce/server/docker/linux)
 
 
 !!! info ""
diff --git a/docs/Knowledge_Base/OS/Linux/Debian/Commands/DNS_Lookup.md b/docs/Knowledge_Base/OS/Linux/Debian/Commands/DNS_Lookup.md
index 181a66a0f..863a0c01e 100644
--- a/docs/Knowledge_Base/OS/Linux/Debian/Commands/DNS_Lookup.md
+++ b/docs/Knowledge_Base/OS/Linux/Debian/Commands/DNS_Lookup.md
@@ -1,10 +1,54 @@
 !!! info ""
 
-    ### DNS Lookup
+    ### Installing dnsutils
 
     ```bash
-    dig -v
     sudo apt-get install dnsutils
+    ```
+
+    ### dnsutils Tools
+
+    When installing dnsutils, you will be able to use the following commands
+    
+    - 'dig'
+    - 'nslookup'
+    - 'nsupdate'
+
+    ### Command syntax
+
+    #### dig
+
+    ```bash
+    dig [server] [name] [type]
+    dig [@server] [-b address] [-c class] [-f filename] [-k filename] [-m] [-p port#] [-t type] [-x addr] [-y name:key] [-4] [-6] [name] [type] [class] [queryopt...]
+
+    dig example.com
+    dig example.com MX
+    dig example.com SOA
+    dig example.com TTL
+    dig example.com ANY +noall +answer
+
+    #reverse lookup
+    dig -x 1.1.1.1 +short
 
-    #dig [server] [name] [type]
+    ```
+
+    #### nslookup
+
+    ```bash
+    nslookup [-option] [name | -] [server]
+    
+    nslookup example.com
+    nslookup -query=mx example.com
+    nslookup -type=soa example.com
+    nslookup -type=any example.com
+    nslookup -timeout=10 example.com
+    nslookup -port 56 example.com
+    nslookup -debug example.com
+    ```
+
+    #### nsupdate
+
+    ```bash
+    nsupdate [-d] [[-y keyname:secret] | [-k keyfile]] [-t timeout] [-u udptimeout] [-r udpretries] [-v] [filename]
     ```
diff --git a/docs/Knowledge_Base/OS/Linux/Debian/Commands/Networking_VLAN_and_Route.md b/docs/Knowledge_Base/OS/Linux/Debian/Commands/Networking_VLAN_and_Route.md
index 6b2ccdcb9..5a43850b4 100644
--- a/docs/Knowledge_Base/OS/Linux/Debian/Commands/Networking_VLAN_and_Route.md
+++ b/docs/Knowledge_Base/OS/Linux/Debian/Commands/Networking_VLAN_and_Route.md
@@ -59,8 +59,8 @@
     #### Network configuration files locations
 
     ```bash
-    nano /etc/NetworkManager/NetworkManager.conf
-    nano /etc/network/interfaces
+    sudo nano /etc/NetworkManager/NetworkManager.conf
+    sudo nano /etc/network/interfaces
     ```
 
 !!! info ""
@@ -239,10 +239,10 @@
 
     ##### Route ADD
 
+    dev syntax depends on how you have those devices set up. You can check by using 'nmcli conn show'
+
     ```bash
     sudo route add -net 0.0.0.0 gw 172.20.0.1 dev VLAN50
-    sudo route add -net 0.0.0.0 gw 172.20.0.1 dev VLAN200
-    sudo route add -net 0.0.0.0 gw 172.20.0.1 dev eth0.35
     sudo route add -net 0.0.0.0 gw 172.20.0.1 dev eth0.50
     ```
 
@@ -262,7 +262,8 @@
     172.20.0.0      0.0.0.0         255.255.240.0   U     400    0        0 VLAN50
     ```
 
-    Table should look like this, if green is missing then if you delete the eth0 route, you can’t reach the device
+    Table should look like this. If you want to delete the eth0 default route so you can force all traffic on a VLAN, you will lose connectivity to the device.
+    In most cases you can regain access if you bounce the Switch port the device is connected to (Disable > wait a few seconds > Enable).
 
     ```bash
     route -n
@@ -335,3 +336,16 @@
     #while in /etc/netplan/
     sudo netplan apply
     ```
+
+!!! info ""
+
+    #### extra commands
+
+    ```bash
+    cat /proc/net/route
+    ip route
+    ip route get x.x.x.x
+    ip route show table local
+    #policy-based routing
+    ip rule show
+    ```